Garage Door Frame Capping in Toronto and the GTA

Why garage door jambs and headers rot or get hit, how we measure, bend and fasten custom aluminum capping, single vs double openings, colour matching and GTA costs.

Updated Written by the Pro Aluminum Siding installation team
On this page
  1. What exactly gets capped on a garage door frame?
  2. Why garage door frames rot or get damaged: 8 common causes
  3. The GTA conditions behind garage frame damage
  4. How to inspect your garage door frame in 15 minutes
  5. Measure, cut, bend, fasten: how we cap a garage door frame
  6. Adhesive, screws or both? Choosing the fastening method
  7. Single vs. double garage openings: what changes?
  8. Coordinating with weatherstripping and your garage door installer
  9. Matching the capping colour to your garage door
  10. Example project scenario: a double garage on a split-level
  11. What does garage door frame capping cost in the GTA?
  12. Homeowner tools: a quote sheet and a care checklist
  13. Serving garages across Toronto and the GTA
  14. Frequently asked questions
  15. Sources

Quick answer: Garage door frame capping wraps the wood header and side jambs around your garage door in custom-bent aluminum. That protects them from bumper scrapes, salty slush and piled snow, and they never need painting again. Pro Aluminum Siding repairs any rot first, then measures, cuts and bends the metal on site and fastens it with adhesive and/or screws. Typical GTA cost: $350–$900 per opening.

  • The bottom 30 cm of each jamb takes the most abuse from salt, slush and snowbanks.
  • Aluminum is bent on site to match your frame’s exact profile, not bought pre-formed.
  • Double openings cost more than singles: longer header, more bends, more handling.
  • Perimeter weatherstripping is removed and refitted (or replaced) as part of the job.
  • We cap frames; we don’t sell, install or service garage doors, openers or springs.
  • 5-year workmanship warranty, written contract, free estimates at (647) 699-3330.

What exactly gets capped on a garage door frame?

A garage door frame is the wood that surrounds the opening on the outside of the house. It has three main parts, and all of them can be wrapped in aluminum.

  • Header: the horizontal piece across the top. It’s usually a wide board or built-up trim, sometimes with a decorative profile.
  • Jambs (side legs): the two vertical pieces on each side. Their front face shows from the driveway, and the inside edge (the return) faces the door.
  • Stop or weatherstrip strip: the narrow piece fastened to the jambs and header, carrying a flexible vinyl or rubber flap that seals against the door. It’s often a combined stop-and-seal product.

Behind the wood trim is the structural framing: a header beam over the opening and studs down each side. Inside the garage, the door’s track brackets are fastened to the jambs, and on most doors the spring assembly is mounted above the opening. Capping covers only the exterior trim. It never touches the door, tracks, springs or opener, and on a properly planned job none of those need to move.

On many GTA homes from the 1960s through the 1990s, garage trim is plain pine or spruce, painted to match the house. Some newer homes use primed finger-jointed trim, which can soak up water quickly at the joints once the paint fails.

Why garage door frames rot or get damaged: 8 common causes

Garage frames take more punishment than any other trim on the house. They sit at ground level, beside the part of your property where cars, shovels and snowblowers spend all winter. Here’s what we see most often, from most to least common.

1. Salty slush thrown up by tires

Every time a car pulls in during winter, slush comes off the tires and wheel wells right at the bottom of the jambs. The City of Toronto says 130,000 to 150,000 tonnes of road salt are typically used on its roads each winter. Some of that rides home on your car. Salt water draws moisture into bare wood, keeps it damp and breaks down paint faster.

2. Snow piled against the jambs

Shovelled and plowed snow ends up stacked on either side of the driveway, often right against the garage frame. It sits there for weeks, melting on sunny afternoons and refreezing overnight. The bottom of the jambs stays wet the whole time.

3. Bumper and mirror strikes

A slight misjudgment pulling in can dent, gouge or split a jamb. Once the paint and wood surface are broken, water gets in. A cracked jamb that’s left for a season or two often turns into a rotted one.

4. Meltwater pooling at the slab

If the driveway slopes toward the garage, or the apron has settled, water collects where the jambs meet the concrete. End grain at the bottom of each jamb soaks it up like a sponge.

5. Failed or missing caulk at the siding or brick

The joint between the jamb and the wall cladding should be sealed. When the caulk cracks, rain driven against the front of the house runs behind the trim.

6. Overflow from the eavestrough above

Many garages sit under a roof edge with a trough above the door. If it’s clogged, sagging or the downspout dumps nearby, water sheets down over the header. Our eavestrough repair service is often part of the same fix.

7. Worn-out perimeter weatherstrip

A hardened, cracked seal lets water and wind-driven snow in along the jamb faces. It also lets meltwater track along the seal’s fastener line into the wood.

8. Shovels, snowblowers and bikes

Everyday impacts add up: a snowblower auger clipping the corner, a bike handlebar, a recycling bin dragged past. Each chip in the paint is a new entry point.

The GTA conditions behind garage frame damage

A few real, checkable facts explain why garage trim here has a hard life. We’ve kept to numbers published by the City of Toronto and federal researchers.

FactWhat it means for a garage frameSource
Toronto typically uses 130,000–150,000 tonnes of road salt each winter, across 14,700 lane kilometres of roads.Salty slush comes home on tires and hits the bottom of the jambs.City of Toronto winter operations fact sheet
Downtown Toronto annual precipitation was around 819 mm (1961–1990 baseline); later normals were slightly higher, and totals are projected to keep rising.More water landing on, and running down, the header and jambs.City of Toronto climate report
December warmed by 1.4°C between 1961–1990 and 1991–2020.Milder early winters can mean more slush and more melt-refreeze at the slab rather than dry cold snow.City of Toronto climate report
Wood decays above about 30% moisture content and won’t decay below about 20%.Keeping the jamb bottoms dry is what stops rot; capping does that job.USDA Forest Products Laboratory
About 58% of Toronto households lived in dwellings built in 1980 or earlier (2021 Census).Lots of original wood garage trim now on its fourth or fifth paint job.City of Toronto 2021 Census backgrounder

The climate report also expects the number of freeze-thaw cycles to decrease over coming decades, but that doesn’t make garage trim safer. Wood rots from staying wet, and a milder winter often means more slush, not less.

How to inspect your garage door frame in 15 minutes

You can tell whether your frame is ready for capping, or needs repair first, with an awl, a flashlight and a tape measure. Pick a dry day.

  1. Open the door fully. This exposes the inside returns of the jambs and lets you see the back of the weatherstrip.
  2. Probe the bottom 30 cm of each jamb. Push an awl in at several points on the front face and the return. If it sinks in easily or brings up crumbly bits, that section is rotted.
  3. Check the end grain at the slab. Look at the very bottom of each jamb. Dark, soft or split end grain is the classic first failure.
  4. Look along the header. Check the top edge for peeling paint, and the ends where the header meets the jambs for open joints.
  5. Inspect the weatherstrip. Bend the flap. If it’s stiff, cracked or no longer touches the door, plan to replace it during capping.
  6. Note any impact damage. Mark dents, splits and gouges with tape so a contractor sees them.
  7. Measure the opening. Record the width across the header and the height of each jamb. Note whether it’s a single or double opening.
  8. Look up and down. Is the trough above overflowing? Does the driveway slope toward the door? Both affect how long any fix lasts.

Cap only, repair first, or something bigger?

Your findings usually point to one of three paths. If the wood is firm everywhere and the only issues are peeling paint and minor dings, the frame can be capped as it is. Soft spots confined to the bottom of a jamb or one end of the header mean a repair first, then capping. If the header is visibly sagging, the jambs have pulled away from the wall, or softness continues into the framing behind the trim, the problem is structural. That needs a general contractor before any trim work makes sense.

If you find soft wood, it needs to come out before the metal goes on. Our frame rot repair process explains the options, from epoxy to new sections. The same methods apply to garage jambs.

Get a written estimate

We measure on site, explain what we found and put the price in writing. Free, with no pressure.

Measure, cut, bend, fasten: how we cap a garage door frame

Capping is custom work. We don’t buy pre-formed garage trim; we bend coil aluminum on site with a brake to match your frame’s exact width, depth and profile. Here’s the full sequence on a typical job.

  1. Remove the weatherstrip and any old capping. The perimeter seal comes off carefully so it can be reused or replaced. Old, dented aluminum is pulled and disposed of.
  2. Inspect and repair the wood. Every soft spot is cut back to sound wood and rebuilt. We also check that the jamb faces are flat and the header is securely fastened, because capping follows whatever shape it covers.
  3. Measure each face. We measure the jamb front, return depth, header face and any decorative steps, at the top, middle and bottom. Old frames are rarely perfectly square, so one measurement isn’t enough.
  4. Cut the coil. Aluminum is cut to width for each piece, allowing for the hems, laps and drip edges the design needs.
  5. Bend the profile on the brake. Each piece is bent into the shape of the trim it covers. Exposed edges get a folded hem so there are no sharp cut edges. The bottom end of each jamb gets a kick-out or turned edge to shed water.
  6. Dry-fit. Pieces are test-fitted before anything is fastened. Corners where the header meets the jambs get the most attention, since they show the most.
  7. Fasten with adhesive and/or screws. Depending on the frame, we bond the capping with exterior construction adhesive, fasten it with colour-matched screws or trim nails in discreet locations, or both. More on choosing below.
  8. Seal the laps and edges. The header overlaps the jambs so water runs over the joint, not into it. Sealant goes at the top edge and along the wall, but the bottom is left able to drain.
  9. Refit or replace the weatherstrip. The seal goes back on over the capped jambs and header, adjusted so it touches the closed door evenly.
  10. Test the door and clean up. We open and close the door to make sure nothing rubs, then remove all offcuts and fasteners from the driveway.

Adhesive, screws or both? Choosing the fastening method

The right fastening depends on how sound the wood is, how flat the face is and how much abuse the frame takes. On garage frames we often combine methods. Adhesive holds the face flat and screws lock the bottom where impacts happen.

FactorAdhesive onlyScrews/trim nails onlyAdhesive + screws
AppearanceCleanest, no visible fastenersSmall colour-matched heads visibleFew fasteners, mostly hidden
Needs a flat, sound surfaceYes, essentialLess criticalYes
Holds up to bumps and impactsModerateGoodBest
Handles aluminum expansionGood if adhesive stays flexibleGood if holes allow movementGood when detailed properly
Temperature limits at installAdhesive has minimum application temperaturesFewAdhesive limits apply
Future removalHarderEasyModerate
Where we typically use itHeaders, smooth facesReturns, patched or uneven woodJamb bottoms on busy driveways

Aluminum moves with temperature, so long runs, especially double-door headers, need fasteners placed to allow a little movement. Pinning a 5-metre header tight at both ends is how capping ends up wavy after the first hot summer.

Single vs. double garage openings: what changes?

The method is the same, but a double opening is more than twice the work of a single. The header is roughly twice as long, which usually means a seam or lap. It also takes more care to keep straight, and needs more attention to expansion.

ConsiderationSingle openingDouble opening
Header lengthUsually fits one piece of coil stockOften needs a planned, overlapped joint
Expansion movementSmallLarger, so fastener layout matters more
Header sag or bowRareMore common on older homes; may need shimming or repair first
Jamb abuseBoth jambs at riskBoth jambs, plus a centre post if there are two doors
WeatherstripShorter runs, cheaper to replaceLonger header seal; more worth replacing during capping
Where it sits in $350–$900Lower to middleMiddle to upper

Two doors side by side

Some houses have two single doors with a centre post between them instead of one wide door. The centre post gets capped on three faces and is usually the most-hit piece on the whole frame. Expect it to be priced close to a double opening.

Decorative headers

Some homes have stepped or built-up headers with several profiles. Each step is its own bend. It’s very doable, but it takes longer than a flat board, and the quote should reflect that.

Not sure what your home needs?

Call and describe what you see. We will tell you honestly whether it is a repair, a replacement or nothing yet.

Coordinating with weatherstripping and your garage door installer

Capping and weatherstripping go together, and the order of work matters. The perimeter seal attaches to the front of the jambs and header. So the capping has to go on first, and the seal goes on top.

If you’re keeping your current door

We remove the existing seal, cap the frame, then refit the seal or install a new one. If the old seal is hard, cracked or short, replacing it at this point costs much less than doing it later, because it’s already off. We’ll mention it in the quote so you can decide.

If you’re getting a new garage door

Pro Aluminum Siding doesn’t sell or install garage doors. If a new door is coming, talk with your installer about timing. There are two workable sequences:

  • Capping first: we repair and cap the frame, then the installer mounts the new door and fits new perimeter seal over our capping. This works well if the opening size isn’t changing.
  • Door first: the installer puts in the door, and we come back to cap the frame and refit their seal. This makes sense if the opening is being altered or new framing is going in.

Either way, ask the installer whether they’ll be fastening anything to the exterior face of the jambs. If they are, it’s better to know before the capping is bent.

Changing the opening size

Widening a single into a double, or changing a garage door opening’s height, is structural work. It typically needs a permit, and it’s outside our scope. Check with your municipality’s building department and a general contractor before planning capping on a changed opening.

Matching the capping colour to your garage door

Most homeowners want the frame to match either the garage door or the house trim. Pre-finished aluminum coil comes in a wide range of standard colours from the common Canadian suppliers. Brands like Kaycan and Gentek are widely used in the GTA market, and most standard white, almond, brown, grey and black tones are easy to source.

Three ways to choose

  1. Match the door. The frame blends into the door, making the opening look like one clean unit. This suits modern flat-panel and carriage-style doors.
  2. Match the house trim. The frame ties into window capping, soffit and fascia. This is the most common choice when a home has consistent trim colour all round.
  3. Contrast on purpose. A dark frame around a light door, or the reverse, can frame the door as a feature. It works best when the same contrast colour shows up elsewhere on the house.

Practical colour tips

  • Hold a coil sample against the door in daylight. Colours look different in a catalogue, under shade, and in full sun.
  • Garage doors fade over time. An older door may no longer match its original colour name, so match what’s there, not what the brochure says.
  • Darker colours hide scuffs better but show salt residue more. Lighter colours show tire marks.
  • If you’re also updating soffit and fascia or siding, pick colours for the whole house together.

Example project scenario: a double garage on a split-level

Example project scenario (illustrative)

This is an illustrative scenario based on typical GTA garage work. It doesn’t describe a real customer or address.

The house: a 1970s split-level with an attached double garage facing the street. The wood frame had been painted many times. A downspout at one corner emptied onto the driveway next to the left jamb.

What we found: the bottom 20 cm of the left jamb was soft, with a split from an old bumper strike. The right jamb was sound but peeling. The header had a slight sag at the centre, and the perimeter seal was stiff and no longer touched the door.

The work: rotted wood on the left jamb was cut out and a new section spliced in. The header was shimmed and refastened so the capping would sit straight. All three pieces were capped in aluminum bent on site to match the door’s colour. We used a planned lap at the header’s centre and adhesive plus screws at the jamb bottoms. A new perimeter seal went on over the capping, and the homeowner had the downspout redirected away from the door.

How it was priced: capping for a double opening, plus a separate line for rot repair and one for new weatherstrip. All three were set out in the written contract.

What does garage door frame capping cost in the GTA?

Typical GTA ballpark ranges (2026). Your written quote after an on-site measure is what counts.

ItemBallpark rangeNotes
Garage door frame capping$350–$900 per openingSingle openings toward the lower end, doubles toward the upper
Wood rot repair before capping$150–$900 per openingOnly if soft wood is found; depends on extent
Entry door frame capping (if done at the same visit)$250–$600 per doorOften the side or front door beside the garage
Window capping (if done at the same visit)$175–$450 per windowFor garage windows or the rest of the house

What moves the price

  • Opening size: single, double, or two singles with a centre post.
  • Rot found: the biggest variable, and the reason we probe before quoting.
  • Header profile: flat boards are fastest; stepped or decorative headers take more bends.
  • Tear-off: removing and disposing of old capping adds time.
  • Colour and gauge: standard colours are quickest; custom colours can cost more.
  • Height and access: high headers or a garage over a slope may need extra staging.
  • Season: adhesives and sealants have temperature limits, which can affect scheduling in cold months.

Combining the garage with other trim on the same visit usually lowers the per-piece cost. Our aluminum capping overview covers the other trim we wrap.

Homeowner tools: a quote sheet and a care checklist

Garage frame measurement and quote sheet

Template: garage door frame measurement and quote sheet

Fill this in before your estimate visit. It helps you compare quotes and makes sure nothing gets missed.

  • Opening type: Single / Double / Two singles with centre post
  • Header width (outside to outside): ______ cm
  • Left jamb height: ______ cm   Right jamb height: ______ cm
  • Jamb face width: ______ cm   Return depth: ______ cm
  • Header profile: Flat / Stepped / Decorative
  • Soft spots found (probe test): Left jamb ____ / Right jamb ____ / Header ____ / Centre post ____
  • Impact damage: ________
  • Weatherstrip condition: Good / Worn / Missing. Replace? Yes / No
  • Colour to match: Door / House trim / Contrast: ______
  • New garage door planned? Yes (installer: ______, date: ______) / No
  • Quoted price: capping ____ / rot repair ____ / weatherstrip ____
  • Warranty, insurance (liability + WSIB) and written contract confirmed? Yes / No

Keeping a capped garage frame in good shape

Capped frames need very little care, but a few habits help them last.

  • Rinse salt residue off the bottom of the jambs with a hose on a mild day in late winter.
  • Keep snowbanks a short distance back from the frame instead of piled against it.
  • Check the sealant at the top of the header and along the wall each spring.
  • Make sure the eavestrough above isn’t overflowing onto the header.
  • Look at the weatherstrip each fall and replace it when it hardens or cracks.
  • Have dents from impacts looked at; a damaged piece can be replaced on its own.
  • Avoid harsh solvents or abrasive pads that can damage the factory finish.

Serving garages across Toronto and the GTA

Our crews travel to homes throughout the region. Garage frame capping is especially common in suburbs built around the car, with front-facing attached garages. Think of the side-split and backsplit streets of Scarborough and the double-garage subdivisions of Brampton. Plenty of our garage work is also in Vaughan and Markham, where many homes from the 1980s and ’90s now have original wood garage trim that’s due for attention.

For a free estimate, call (647) 699-3330 or send us a photo of your garage frame through the online estimate form.

Book a free on-site measure

Every job comes with a written contract and our 5-year workmanship warranty.

Frequently asked questions

Can you cap a garage door frame that already has some rot?

Yes, but the rot has to be repaired first. We cut out soft wood, rebuild it with epoxy, a spliced-in section or a new piece, and only then install the aluminum. Capping over decayed wood traps moisture and lets the rot keep spreading out of sight, and fasteners won’t hold properly in soft wood.

Do I need to remove my garage door for capping?

No. The door stays in place and keeps working during the job, apart from short periods when we need it open or closed to reach a section. We work only on the exterior trim. The door, tracks, springs and opener aren’t touched. We’ll just ask you to keep the car out of the way while we work.

How long does garage door frame capping take?

Most single openings are capped in part of a day once any rot repair is done. Double openings, decorative headers or significant rot can push it to a full day. Adhesive and sealant curing don’t usually stop you using the door, but we’ll tell you if a section needs to stay undisturbed for a few hours.

Will capping fix a door that doesn’t seal at the sides?

Capping on its own doesn’t, but the job is the best time to fix it. Because the perimeter weatherstrip comes off for capping, we can install a new one over the aluminum and adjust it to meet the door evenly. Gaps caused by a door that’s out of adjustment need a garage door technician.

Do you install or repair garage doors?

No. Pro Aluminum Siding caps and repairs the wood frame around the door, but we don’t sell, install or service garage doors, openers, tracks or springs. If your door needs work, contact a qualified garage door company. We’re happy to coordinate timing with them so capping and any new weatherstrip go on in the right order.

Can capping be done in winter?

Sometimes. Bending and screw-fastening aluminum can be done in cold weather, but construction adhesives and sealants have minimum application temperatures, and rot repair needs dry wood. We generally schedule garage capping from spring to late fall and book winter jobs only when conditions suit the materials being used.

How do you match the colour to my garage door?

We bring coil samples and hold them against your door in daylight, since doors fade and catalogue names don’t always match what’s on the house. Standard colours from the common Canadian suppliers cover most doors. If you’d rather match house trim or go for a deliberate contrast, we can show those options at the same time.

Will the capping dent if I hit it with the car?

Aluminum can dent from a hard hit, just as wood would split. The advantage is that a damaged capping piece can usually be replaced on its own without redoing the frame, and the wood underneath stays protected. Using adhesive plus screws at the jamb bottoms helps the capping resist the lighter knocks it takes every day.

Is a permit required for garage door frame capping?

Capping existing trim generally doesn’t need a building permit. The City of Toronto, for example, lists re-cladding a house of three storeys or less with non-combustible material, other than brick or stone veneer, as not requiring one. Changing the opening’s size is structural and typically does. Always confirm with your own municipality’s building department.

Sources

Call Now: (647) 699-3330