On this page
- What counts as a window or door frame, and which parts rot first?
- 7 signs your window or door frame has wood rot
- How to do the probe test on your own frames
- Why do window and door frames rot in the first place?
- What we check: our frame inspection framework
- Repair options, from smallest to largest
- How a frame repair job runs, step by step
- Entry door frames and thresholds need extra attention
- Example project scenario: a 1950s bungalow with soft sills
- When repair isn’t enough: signs you need a new window or door
- What does window and door frame repair cost in the GTA?
- Before you book: a checklist and a quote worksheet
- Where we do frame repairs around the GTA
- Frequently asked questions
- Sources
Quick answer: Rotted window and door frames can usually be repaired rather than replaced. Pro Aluminum Siding probes every sill, jamb and brickmould, cuts out soft wood, then rebuilds it with epoxy, spliced-in new wood or replacement sections. After that we cap it in custom-bent aluminum so water can’t get back in. Across the GTA, rot repair typically runs $150–$900 per opening before capping.
- Most rot starts at the bottom: sills, the lower ends of brickmould and the base of door jambs.
- Repair options range from epoxy consolidation to a full exterior frame rebuild, depending on how deep the decay goes.
- Aluminum capping goes on only after the wood underneath is solid and dry.
- We repair frames; we do not sell or install new windows or doors.
- Every job comes with a written contract and a 5-year workmanship warranty.
- Free estimates by phone at (647) 699-3330 or through our online form.
What counts as a window or door frame, and which parts rot first?
The exterior frame is the wood that surrounds the glass unit or door slab and ties it into the wall. On most GTA houses built before the 1990s it’s real wood: pine, fir or sometimes cedar. Even newer homes often have wood brickmould or sills behind a coat of paint.
Rot almost always starts in the same few places. Water lands on horizontal surfaces, runs to the low points and sits in the joints. So the order of failure is predictable:
- Sill (window) or threshold area (door): the sloped bottom piece that sheds water. It gets the most rain, snowmelt and splashback.
- Bottom ends of the brickmould: the decorative outer trim. End grain at the bottom soaks up water like a straw.
- Lower jambs: the vertical side pieces, especially where they meet the sill.
- Mitred corners at the head: joints open up as the wood swells and shrinks, letting water in from above.
- Stops and mullions: the thin strips holding glass or separating units, often forgotten when painting.
The paint can look acceptable while the core of the sill is gone. Much of what we find is decay painted over two or three times.
7 signs your window or door frame has wood rot
The clearest sign is wood that gives under pressure. Peeling paint and stains are early warnings.
1. Paint that blisters or peels on the sill but not elsewhere
Paint fails first where moisture pushes out from behind it. If the sill and the bottom 15 cm of the brickmould are peeling while the head trim looks fine, water is getting into the wood from below or through joints.
2. Paint that cracks along the grain in a checkerboard pattern
Long cracks across the grain, called “alligatoring,” mean the wood is swelling and shrinking more than the paint can stretch. That cycling is a sign the wood is regularly getting wet.
3. Dark grey or black staining at joints
Staining where the sill meets the jamb, or at the bottom of the brickmould, is often fungal growth or water carrying tannins out of the wood. It’s not proof of rot, but it’s where we probe first.
4. Wood that feels soft or spongy
Press firmly with your thumb. Sound wood doesn’t dent. Wood that dents, crumbles or feels like cork is decayed.
5. Cracked or missing caulk around the frame
Caulk between the brickmould and the brick or siding is the first defence. Once it shrinks, cracks or pulls away, every rainstorm sends water into the gap behind the trim.
6. Staining, bubbling or mould on the inside
Look at the interior sill, the drywall below the window and the trim around the inside of the door. Water stains, swollen MDF trim or bubbling paint inside often trace back to a failed exterior sill.
7. A door that sticks, drags or won’t latch
When the bottom of a door jamb rots, the frame can drop or twist slightly. The door then rubs at the top or misses the strike plate. It’s a frame problem, not a hinge problem.
How to do the probe test on your own frames
A probe test tells you whether wood is solid or decayed, and you can do it in about ten minutes per window. All you need is an awl or a small flat screwdriver, a flashlight and a notepad.
- Start at the sill’s outer edge. Push the tip of the awl in at a slight angle about 1 cm from the front edge. Sound wood resists and the tip goes in a millimetre or two. Decayed wood lets it sink in easily.
- Move along the sill in 5 cm steps. Rot is rarely uniform. Note where the soft area starts and stops, because that decides whether a partial repair is possible.
- Probe the bottom ends of the brickmould. Go right to the bottom, where end grain sits on or near the sill. This is the single most common soft spot we find.
- Check the jamb-to-sill joint. Probe the corner from both faces. A soft corner often means water has been tracking down the joint for years.
- Look at what comes out. If the tip lifts out long splinters, the wood is still fibrous and sound. If it brings up short, crumbly bits or brown cubes, that’s brown rot.
- Check the inside. Look under the interior sill and at the drywall below for stains or soft spots, and note them with the exterior findings.
- Write it down per opening. Record which window or door, which piece and roughly how far the soft area runs. This makes contractor quotes much easier to compare.
Why do window and door frames rot in the first place?
Wood rots when it stays wet long enough for fungi to grow. Researchers at the U.S. Forest Products Laboratory note that it’s well understood that wood will decay above 30% moisture content and will not decay below 20%. Wood kept below that lower limit has a margin of safety against fungal decay. So the real question is always: what keeps this piece of wood wet?
That matters a lot in Toronto. The City’s climate report puts downtown annual precipitation at around 819 mm in the 1961–1990 baseline, slightly higher in 1991–2020. It projects annual totals rising by roughly 11% by the 2080s under a medium scenario. More rain on old trim means more chances for wood to cross that moisture threshold.
Failed or missing caulk
Caulk is the most common entry point. Sun and cold break caulk down, and once a joint opens, water runs behind the brickmould and sits against the sheathing and frame.
No drip edge or a flat sill
A sill should slope away from the window and have a drip groove underneath, so water falls off instead of curling back to the wall. Many replacement windows from the 1980s and ’90s were set on old sills that were cut down, flattened or missing the drip. Water sits on a flat sill and soaks in.
Splashback and snow
Basement and ground-floor windows, and every entry door, get water bouncing up from walkways, decks and garden beds. In winter, snow piles against low frames and melts slowly on sunny days. That keeps the bottom few centimetres wet for weeks.
Overflowing or missing eavestroughs
If a trough is clogged or a downspout dumps near a door, sheets of water run down the wall and over the frame below. Fixing the frame without fixing the eavestrough overflow above it just resets the clock.
Old capping that trapped water
Badly installed aluminum capping can make things worse. If old capping was face-nailed with no sealant, or bent without a drip, water gets behind it and can’t escape. We often find the worst rot under 30-year-old capping. That’s why we always pull it and inspect before re-capping.
What we check: our frame inspection framework
We assess every opening on the same checklist, so the quote reflects what’s actually there rather than a guess. This is the framework our estimators use on site. You can use it to sanity-check any quote you get.
| Component | What we test | Typical finding | What it usually leads to |
|---|---|---|---|
| Sill (top surface) | Probe every 5 cm, check slope and drip | Soft at front edge or ends | Epoxy, Dutchman splice or sill replacement |
| Brickmould ends | Probe bottom 20 cm, check end grain | Soft bottom 5–15 cm | Cut back and splice, or replace a section |
| Jamb-to-sill joint | Probe both faces, look for gaps | Open joint, softness at corner | Rebuild corner with epoxy or new wood |
| Caulk lines | Visual and touch | Cracked, shrunk or missing | Remove and replace with new sealant |
| Interior finishes | Look for stains, swelling, mould | Stain under inside sill | Confirms exterior water entry |
| Sheathing behind trim | Checked once trim is removed | Dark or soft sheathing | Expanded scope, discussed before proceeding |
| Water sources above | Eavestrough, flashing, roof edges | Overflow onto the frame | Fix the source too, or the repair won’t last |
The last two rows are why a quote should say, in writing, how hidden damage found under the trim will be handled.
We measure on site, explain what we found and put the price in writing. Free, with no pressure.
Repair options, from smallest to largest
The right repair depends on how deep the rot goes and how much sound wood is left around it. We always pick the smallest repair that will actually last. Here are the four main options.
Option 1: Consolidant and epoxy filler
Best for small, shallow soft spots, such as a corner of a sill or the bottom few centimetres of brickmould. We dig out the loose, crumbly material and let the wood dry. Then we soak the remaining fibres with a liquid epoxy consolidant, which hardens the slightly soft wood around the cavity. Finally we fill and shape the void with a two-part epoxy wood filler.
Epoxy bonds to wood, doesn’t shrink like old putty and can be sanded and shaped to match the profile. It’s not a fix for wood that’s soft all the way through. If more than about a third of the piece is affected, a splice or replacement usually lasts longer.
Option 2: Partial “Dutchman” splice
A Dutchman is a patch of new wood set into the old. We cut out the decayed section with clean, square or angled cuts back to solid wood. Then we shape a new piece of rot-resistant or treated stock to fit exactly, and glue and fasten it in. The joint is sealed and primed so it doesn’t become the next weak spot.
This is ideal when one end of a sill or the bottom of a brickmould leg is gone, but the rest is sound. It keeps the original frame, the window unit and the interior trim undisturbed.
Option 3: Replacing sill or brickmould sections
When a whole sill is soft or the brickmould is rotted along most of its length, we replace the piece. A new sill is cut to match the original slope and given a proper drip groove underneath. That detail alone fixes the cause on many older windows. New brickmould is milled to a matching or close profile.
Because the window unit stays in place, this is still frame repair, not window replacement. It’s often the most cost-effective long-term fix on a 1950s–1970s house with sound windows but tired wood around them.
Option 4: Full exterior frame rebuild
Sometimes the sill, both brickmould legs and the lower jambs are all decayed. In that case we rebuild the whole exterior frame around the existing window or door: new sill, new brickmould and new exterior jamb extensions, tied into solid wood. This is the largest repair we do, and it’s quoted after we’ve opened things up enough to see the extent.
If the rot has reached the window’s own frame or the structural framing of the wall, the job has moved beyond frame repair. We cover that further down.
Epoxy vs. splice vs. section replacement: which is right?
Each repair method has a sweet spot. Here is how they compare on what matters to homeowners.
| Factor | Epoxy consolidant & filler | Dutchman splice | Section replacement | Full exterior frame rebuild |
|---|---|---|---|---|
| Best for | Small, shallow soft spots | One end or leg badly rotted, rest sound | Whole sill or most of a brickmould leg | Sill, both legs and lower jambs |
| Keeps original wood | Most of it | Most of it | Some | Little |
| Fixes a missing drip/flat sill | No | Partly | Yes | Yes |
| Disturbs interior trim | No | Rarely | Sometimes | Sometimes |
| Where it sits in the $150–$900 range | Low end | Low to middle | Middle to high | High end, or quoted separately if extensive |
| Limitation | Not for wood soft all the way through | Joint must be sealed well | Profile matching can take time | May uncover deeper damage |
Most houses need a mix of methods, so the quote should list the method per opening, not one lump number.
How a frame repair job runs, step by step
A standard frame repair takes from a couple of hours for a single window to a full day or two for a whole house. The order of work is what makes it last.
- Remove old capping and caulk. Any existing aluminum is pulled so we can see the wood. Old caulk is cut out completely, not painted over.
- Probe and mark. Every soft area is marked, photographed and measured. If it’s bigger than expected, we stop and talk to you before going further.
- Cut back to sound wood. Decay is removed until the awl meets solid resistance. Leaving soft wood behind is the main reason repairs fail.
- Let it dry and treat it. Exposed wood needs to be dry before epoxy or glue will bond. We may treat sound wood with a preservative or consolidant.
- Rebuild. Epoxy fill, splice or new sections go in, glued and fastened with corrosion-resistant fasteners.
- Shape, prime and seal. Repairs are shaped to match the original profile, all end grain is sealed, and the joints get fresh sealant.
- Cap or paint. Most homeowners choose aluminum capping at this point so the repaired wood never sees weather again. Others prefer to paint and keep the wood visible.
- Walk-through. We show you the photos of what we found and what we fixed, and confirm the warranty terms in writing.
Why capping comes next
Once the wood is sound, aluminum capping is the best way to keep it that way. Custom-bent aluminum sheds water off the sill and away from end grain. It never needs painting, and it closes off the joints that let water in originally. Done right, the wood underneath stays dry enough that it simply stops being a maintenance item.
The details make the difference: a bent drip edge on the sill, sealant at laps and edges, and fasteners placed where water won’t track in. We cover materials, colours and how we bend profiles on our aluminum capping overview. If your frames already have capping that’s dented or faded but the wood underneath is sound, that’s a straight window capping replacement job instead.
Entry door frames and thresholds need extra attention
Door frames rot faster than window frames because they sit at ground level and get foot traffic, splashback and snow. The bottom 10–20 cm of each jamb and the brickmould legs are the usual problem. Behind them, the wood under the threshold can also be soft.
Thresholds and sills under doors
On older homes, the wood sill under an aluminum or oak threshold can rot from below while the threshold looks fine. If it’s limited to the exterior edge, we can usually splice in new wood and cap the exposed face. If the sill under the door is rotted right through, or the subfloor below has gone soft, that’s a bigger repair. It may involve removing the door, and we’ll tell you honestly whether it’s in our scope.
Capping door frames
After repair, door frames get the same treatment as windows: custom-bent aluminum on brickmould and exposed jamb faces, with sealant at the bottom. We leave a small gap above the step so the metal doesn’t sit in water. Entry door frame capping typically runs $250–$600 per door, on top of any rot repair needed.
If the door sits under a porch roof that’s also showing its age, our porch repair work can be done at the same visit.
Call and describe what you see. We will tell you honestly whether it is a repair, a replacement or nothing yet.
Example project scenario: a 1950s bungalow with soft sills
Example project scenario (illustrative)
This scenario is illustrative, based on the kind of job we see often in older GTA neighbourhoods. It doesn’t describe a specific customer or address.
The house: a 1950s brick bungalow with original-style wood sills and brickmould around replacement vinyl windows installed in the 1990s. The old aluminum capping on the front windows was dented and loose. The back door frame had been painted many times.
What the inspection found: Two front windows had soft spots only at the outer ends of the sill. They got epoxy consolidation and filler. One side window had a sill that was soft along most of its length with no drip groove, so it got a new sill. The back door had both brickmould legs rotted about 15 cm up from the step. We spliced new wood into both, and the threshold area was sound.
The cause: The old capping had been face-nailed with no sealant, so water got behind it. A clogged downspout at the back corner was also dumping water on the landing next to the door.
The fix: repair as above, then new custom-bent aluminum capping on all four openings with drip edges on the sills. The homeowner also arranged to have the downspout extended away from the door.
How the price was built: each opening was quoted separately for rot repair plus capping, and the contract set out how any hidden damage would be priced.
When repair isn’t enough: signs you need a new window or door
Frame repair has limits. If the window or door unit itself has failed, fixing the wood around it only protects a product that still needs replacing. We’ll tell you straight when that’s the case.
Pro Aluminum Siding does not sell or install windows or doors. When a unit needs replacing, we recommend you talk to a dedicated window and door installer. Once the new unit is in, we’re happy to come back to repair surrounding trim and cap the frame.
Signs the unit, not just the frame, is the problem
- Fogging or condensation between the panes of a sealed glass unit.
- Rot in the window’s own sash or frame, not just the surrounding trim.
- A door slab that’s warped, delaminated or rotted at the bottom rail.
- Drafts that persist after new weatherstripping and caulking.
- Rot that has reached the wall’s structural framing around the opening.
Repair vs. replace at a glance
| Situation | Frame repair + capping | Window or door replacement (by an installer) |
|---|---|---|
| Unit works well, trim is rotted | Best choice | Not needed |
| Sill rotted, glass unit sound | Usually yes | Only if you want an upgrade anyway |
| Fogged glass, rotted sash | Won’t fix the unit | Usually the right call |
| Door slab warped or rotted | Frame only | Slab or full unit replacement |
| Rot into wall framing | Beyond our scope | Installer and possibly a general contractor |
| Planning new windows within a year or two | Minor stopgap only | Do it first, then cap the new frames |
Permits when a unit is replaced
The City of Toronto says replacing a window or door in an existing opening of a detached or semi-detached house generally doesn’t need a building permit. That holds as long as the opening isn’t enlarged or relocated, structural support isn’t affected, and no new exit is created. New, larger or moved openings do need a permit. Other GTA municipalities have their own rules, so check with your local building department before work starts.
If you’re replacing windows and siding in the same year, sequence matters. Windows go in first, then trim and capping, then new aluminum siding laps neatly up to finished frames.
What does window and door frame repair cost in the GTA?
Typical GTA ballpark ranges (2026). Your written quote after an on-site measure is what counts.
| Work | Ballpark range | What moves it |
|---|---|---|
| Wood rot repair before capping | $150–$900 per opening | Extent of rot; epoxy vs. splice vs. new sections |
| Window capping | $175–$450 per window | Size; sill and brickmould complexity |
| Entry door frame capping | $250–$600 per door | Frame width, sidelights, threshold detail |
| Full exterior frame rebuilds, deeper damage | Quoted per project | What’s found once trim is removed |
Factors that push the price up or down
- Height and storeys: second-storey and dormer windows need ladders or staging.
- Rot found: the biggest variable, which is why we probe before quoting.
- Colour and gauge: standard colours are quickest to source; custom colours can cost more.
- Custom bends: deep or unusual profiles and bay windows take longer.
- Season: epoxy and sealants need mild temperatures.
Grouping openings usually lowers the per-window cost. Many homeowners combine frame repair with capping their garage door frame on the same visit.
Before you book: a checklist and a quote worksheet
Homeowner checklist
- Probe-test every exterior sill and brickmould leg and note the soft spots.
- Look up: is an eavestrough or downspout pouring onto any frames?
- Decide whether any windows or doors will be replaced in the next few years.
- Ask each contractor to list the repair method per opening.
- Confirm how hidden damage will be priced if it’s found.
- Pick capping or paint for the finish, and choose a colour.
- Get the warranty and scope in a written contract.
Questions to ask any frame repair contractor
Template: frame repair quote comparison worksheet
Copy this for each contractor and fill it in during or after the estimate visit.
- Did they probe the wood, or only look? Probed / Looked only
- Repair method per opening: Window 1 ____ / Window 2 ____ / Door ____
- Will old capping and caulk be fully removed? Yes / No
- How is extra hidden rot priced? Per hour / Per piece / Fixed allowance / Not stated
- Finish: Aluminum capping (colour ____ ) / Paint
- Cause of rot identified and addressed? ________
- Workmanship warranty length and terms: ________
- Liability insurance and WSIB provided? Yes / No
- Written contract? Yes / No
- Total, and price per opening: ________
Where we do frame repairs around the GTA
Our crews travel to homes across Toronto and the surrounding region. Older housing stock is where frame rot shows up most. In the City of Toronto’s 2021 Census backgrounder, about 29% of households lived in dwellings built in 1960 or before, and another 29% in dwellings from 1961 to 1980. That’s a lot of original wood trim reaching the end of its paint cycles.
We see plenty of this work in the wartime and postwar houses of East York and the bungalows of Etobicoke. Older sections of Mississauga and Oakville keep us busy too. Wood brickmould on 1980s and ’90s homes is now failing too. See every community we visit on our service areas page.
To book a free estimate, call (647) 699-3330 or send photos through our free estimate form.
Every job comes with a written contract and our 5-year workmanship warranty.
Frequently asked questions
Can rotted window sills be repaired instead of replaced?
Yes, in most cases. If the rot is limited to the ends or front edge, epoxy consolidant and filler or a Dutchman splice can restore the sill. If the whole sill is soft or it has no drip groove, we replace the sill itself while leaving the window in place. Only when the window’s own frame or the wall framing has rotted is window replacement the better path.
Is it okay to cover rotted wood with aluminum capping?
No. Capping over decayed wood hides the problem without stopping it. Moisture trapped under the metal keeps the rot going, and fasteners eventually loosen in soft wood. Proper practice is to remove the rot, rebuild with sound material, let it dry, seal it and then cap. Any quote that skips the repair step should be questioned.
How long does epoxy wood repair last?
A well-done epoxy repair on a small area can last many years, especially under capping where it isn’t exposed to sun and water. It depends on removing all the decayed wood first, using epoxy on dry wood, and fixing the water source. Epoxy is the wrong choice when the piece is soft all the way through; that needs a splice or new section.
Do you install new windows or doors?
No. Pro Aluminum Siding repairs and caps window and door frames, but we don’t sell or install windows or doors. If your unit has failed, such as fogged glass, a rotted sash or a warped door slab, we’ll say so honestly and suggest you consult a window and door installer. We can then repair trim and cap the frame once the new unit is in.
How do I know if the rot has spread into the wall?
Signs include soft or stained drywall below a window, a musty smell, a door frame that keeps shifting, or softness that continues past the trim into the sheathing. We often can’t confirm it until the exterior trim is removed. If we find structural framing damage, we stop and discuss it with you, since that work goes beyond frame repair.
How much does it cost to fix a rotted window sill?
As a GTA ballpark for 2026, rot repair before capping runs $150–$900 per opening, depending on whether it needs epoxy, a splice or a new sill. Capping the window afterwards typically adds $175–$450. Your written quote after we probe the wood on site is the number that counts.
Is the repair covered by a warranty?
Yes. Our work comes with a 5-year workmanship warranty, set out in the written contract along with the scope for each opening. The warranty covers our installation and repair work. It doesn’t cover new damage from causes outside our scope, such as an eavestrough overflowing onto the frame, which is why we point those out during the inspection.
Do I need a permit for frame repairs?
Repairing and capping existing trim generally doesn’t need a building permit. Changing the size or location of an opening, or doing structural work, usually does. Rules vary by municipality, so confirm with your local building department. The City of Toronto, for example, exempts replacing windows and doors in existing openings of houses when the opening and structure aren’t changed.