On this page
- Why seamless aluminum is the GTA standard
- 5-inch or 6-inch eavestrough: when is bigger worth it?
- How many downspouts do you need, and where should they go?
- Toronto’s downspout disconnection rules: what homeowners need to know
- Slope and hangers: the two details that decide whether troughs work
- Ice dams and winter damage: what’s really happening at the roof edge
- Mature trees and leaf load: keeping troughs flowing
- Repair or replace? 8 signs that point one way or the other
- What does eavestrough installation cost in the GTA?
- How a seamless eavestrough is installed
- Example project scenario: a two-storey under mature maples
- Template: a seasonal eavestrough care calendar
- Quick facts behind the advice
- Eavestrough service across Toronto and the GTA
- Frequently asked questions
- Sources
Quick answer: For most GTA homes, a seamless aluminum eavestrough formed on site, hung on hidden hangers into solid fascia and sloped toward properly placed downspouts, is the reliable choice. Ballpark 2026 pricing is $8–$14 per linear ft for 5″ and $10–$17 for 6″, with downspouts at $10–$18 per linear ft. In Toronto, downspouts must also be disconnected from the sewer.
- Seamless troughs are formed in one piece per run, so the only joints are at corners and ends.
- 6″ troughs carry noticeably more water than 5″ and are worth it on large or steep roof planes and under heavy tree cover.
- The City of Toronto requires all property owners to disconnect downspouts from the sewer system; other GTA municipalities set their own rules.
- A trough is only as strong as the fascia behind it, so rotten boards are fixed before new eavestrough goes up.
- Licensed, fully insured (liability and WSIB), written contract, 5-year workmanship warranty, free estimates.
Why seamless aluminum is the GTA standard
Seamless aluminum eavestrough is popular here because it removes the weakest point of older systems: the joints. Sectional troughs come in short lengths joined with connectors and sealant, and every one of those joints eventually leaks after enough freeze-thaw cycles.
A seamless trough is roll-formed from a coil of prefinished aluminum on a machine brought to your house. Each run is cut to the exact length of that wall, so a 40-foot eave gets one 40-foot piece. The only seams left are the mitred corners and end caps, which are sealed and riveted.
Why aluminum rather than vinyl or steel?
Aluminum doesn’t rust, it’s light enough to hang without stressing the fascia, and it comes in a wide range of baked-on colours. The table shows how it stacks up against the alternatives.
| Material | Joints | Cold-weather behaviour | Corrosion | Typical fit |
|---|---|---|---|---|
| Seamless aluminum | Corners and ends only | Stays flexible; can dent under heavy ice | Does not rust | Most GTA houses |
| Sectional aluminum | Every 10 ft or so | Joints loosen over time | Does not rust; joints leak | Short repairs, sheds |
| Vinyl | Frequent snap joints | Can crack in deep cold | None, but UV fades | Budget DIY, outbuildings |
| Galvanized steel | Sectional or seamless | Strong under load | Rusts once coating fails | Some commercial or high-load uses |
| Copper | Soldered | Very durable | Develops patina, no rust | Heritage or high-end homes |
5-inch or 6-inch eavestrough: when is bigger worth it?
A 5″ K-style trough handles the roof on most GTA bungalows and modest two-storeys. Step up to 6″ when one trough collects water from a large or steep roof plane, when an upper roof drains onto a lower one, or when mature trees drop heavy leaf loads that would quickly choke a smaller trough.
The size refers to the width across the top of the trough. Going from 5″ to 6″ sounds small, but the trough gets deeper and wider at the same time, so it holds and moves a good deal more water. It also pairs with larger downspouts, which is often where the real capacity gain comes from.
| Factor | 5″ seamless | 6″ seamless |
|---|---|---|
| Ballpark price (2026) | $8–$14 per linear ft | $10–$17 per linear ft |
| Common downspout pairing | 2″ x 3″ | 3″ x 4″ |
| Best for | Average roof planes, moderate pitch, light tree cover | Large or steep planes, long runs, upper roofs dumping onto lower ones, heavy leaf fall |
| Clog tolerance | Moderate | Higher; leaves pass to larger outlets more easily |
| Look | Proportional on smaller houses | Bolder; suits taller houses and deep fascia boards |
| Fascia requirement | Standard boards | Needs a fascia board deep enough to mount it cleanly |
Five situations where 6″ usually pays off
- Long, unbroken runs. The longer the trough, the more water piles up at the outlet during a downpour.
- Steep roofs. Water comes off faster and can overshoot or overwhelm a 5″ trough at its peak.
- Upper roofs draining onto lower roofs. The lower trough receives its own water plus the upper roof’s.
- Big trees directly overhead. Wider outlets and bigger downspouts are less likely to block with leaves and seed pods.
- Repeated overflow at one corner. If a single valley floods every storm, upsizing that section (or adding a downspout) is often the fix.
A mixed approach is common: 6″ on the problem side or the big back slope, 5″ everywhere else. We’ll show you on the estimate where each size makes sense rather than upselling the whole house.
How many downspouts do you need, and where should they go?
You need enough downspouts that no stretch of trough is carrying more water than its outlet can drain, and they should sit where the discharge can flow away from the house safely. On long runs that often means a downspout at each end, with water sloping away from the middle.
Sizing
Standard residential downspouts are 2″ x 3″ and 3″ x 4″. The larger size moves considerably more water and is far less likely to clog with leaves. A 3″ x 4″ downspout is often worth it even on a 5″ trough under trees, provided the outlet is cut to match.
Placement rules of thumb
- Place outlets at the low ends of runs, near corners, where the downspout can run straight down the wall with as few bends as possible.
- Avoid dumping water onto walkways, driveways, stairs or patios, where it can freeze in winter.
- Keep discharge away from window wells, basement entrances and spots where the ground slopes back toward the foundation.
- On upper roofs, route downspouts into the lower trough only if that lower trough is sized for it; otherwise run them to the ground.
- Consider where the extension or splash pad will sit, especially in Toronto, where downspouts now discharge onto your property rather than into the sewer.
Toronto’s downspout disconnection rules: what homeowners need to know
In the City of Toronto, it is mandatory for all property owners to ensure their downspouts are disconnected from the City’s sewer system. The City’s mandatory downspout disconnection page says the work must be done in accordance with the Property Standards Bylaw (§629-20, roofs and roof structures).
The City explains why: heavy rain can overload sewers, which raises the risk of basement flooding and can release polluted rainwater into local waterways. Directing roof water onto the ground instead eases that load.
What the City says about where the water goes
- Water should flow away from the building’s foundation.
- It must not damage a neighbour’s property, and it should not flow onto a driveway or sidewalk, or directly onto a City sidewalk.
- A downspout extension carries water away from the house, and a splash pad at the end helps direct flow and prevent erosion.
- The open sewer standpipe left after disconnection should be capped to keep out water, debris and animals.
- If you use a rain barrel, the City advises removing it in winter and adding an extension for drainage.
- The City also recommends cleaning eavestroughs at least twice a year and repairing leaks and sagging sections.
Exemptions and financial help
The City may grant an exemption where disconnection is hazardous or not technically feasible, but before applying you’re expected to try relocating downspouts, re-grading eavestroughs or correcting the property’s slope. That’s exactly where new eavestrough layout can help: moving an outlet to a different corner often solves a disconnection problem that seemed impossible.
The City also runs a financial assistance program that reimburses labour and materials up to $500 for eligible low-income seniors and people with disabilities who own a residential property in Toronto, with a combined household income of $50,000 or less. Applications are due within one year of completing the work. Check the City’s page for current eligibility details and forms before you rely on it.
If a disconnection leaves water heading somewhere it shouldn’t, tell us during the estimate. Re-planning outlet positions is part of designing a new eavestrough layout.
We measure on site, explain what we found and put the price in writing. Free, with no pressure.
Slope and hangers: the two details that decide whether troughs work
An eavestrough that looks perfectly level is usually wrong. It needs a slight, consistent pitch toward each downspout so water keeps moving, and it needs hangers close enough together to carry water, debris and ice without sagging.
Getting the slope right
A common trade guideline is a drop of roughly 1/4″ to 1/2″ for every 10 feet of trough. Too little and water sits in the trough, freezes in winter and breeds mosquitoes in summer. Too much and the trough looks visibly crooked against the roofline and the low end may sit too far below the shingles to catch runoff.
On long runs we often pitch from the middle down to a downspout at each end, which keeps the drop small and the line looking straight from the street.
How to check your own slope (from the ground or a safe step)
- Wait for a steady rain, or run a hose. A garden hose at the high end of the trough, placed by someone on a secure ladder with a helper, shows the flow clearly.
- Watch where water pools. Water that stops moving midway, or ponds just short of the outlet, points to a dip or a reverse slope.
- Look along the trough line. From the end of the house, sight down the front edge. Sags between hangers show as dips.
- Check after a freeze. Ice that builds in one spot every winter is often a low point holding water.
- Note overflow points. Water spilling over the front in a storm usually means a clog, an undersized outlet or a slope problem nearby.
Hangers and fasteners
Modern seamless troughs use hidden hangers that clip inside the front lip and screw through the back of the trough into the fascia. Older systems often used spikes and ferrules driven through the trough, which loosen with every freeze-thaw cycle and let the trough droop.
Spacing hangers more closely helps in snow country. A trough full of ice or wet leaves is very heavy, and that weight is carried entirely by hangers and the fascia they’re screwed into. Hangers into rotten wood will fail regardless of spacing, which is why fascia condition comes first. Our soffit and fascia replacement page explains how soft boards are dealt with before new trough goes up.
Ice dams and winter damage: what’s really happening at the roof edge
Ice dams form when heat escaping from the house melts snow on the upper roof, and that meltwater refreezes at the cold eave. The eavestrough doesn’t cause ice dams, but it’s often where the damage shows: bent hangers, troughs torn off the fascia, and ice spilling over the front.
Natural Resources Canada notes that ice damming usually happens when there’s a significant amount of snow on the roof, and that the preferred prevention is sealing air leaks and insulating well so the attic stays cold. A well-ventilated attic is also less prone to ice dams at the eaves.
Winter damage we see most often
- Troughs pulled forward or down by the weight of ice, especially where hangers were widely spaced or screwed into soft wood.
- Split corner seams where expansion and contraction have worked the sealant loose.
- Crushed downspout elbows from ice blocking the bottom and refreezing inside.
- Icicles over doors and walkways from a trough that overflows at one spot every melt.
What eavestrough work can and can’t fix
Good eavestrough work limits the damage: closer hanger spacing, solid fascia, a correct slope so water drains before it freezes, and downspouts that discharge away from walkways. It can’t stop ice dams caused by a warm attic. If you see thick ice along the eaves every winter, talk to an insulation or roofing professional about air sealing, insulation and ventilation as well.
Mature trees and leaf load: keeping troughs flowing
Under big trees, the most important thing is sizing and access: bigger outlets and downspouts, and a trough you can actually clean. Toronto is a leafy city. The City’s CanopyTO 2018 study estimated tree canopy cover at 28.4% to 31%, and found Norway maple was the most common street tree, at 13.5% of the street tree population. Maples drop leaves in fall and winged seeds in spring, both of which pack into troughs.
Practical ways to handle heavy leaf fall
- Upsize the outlets and downspouts. A 3″ x 4″ downspout clears debris far more reliably than a 2″ x 3″.
- Consider 6″ troughs on the tree side. More volume means a light layer of leaves doesn’t immediately cause overflow.
- Reduce bends. Every elbow is a place for leaves to catch, so straight runs from outlet to ground are best.
- Clean at the right times. In a maple-heavy yard, late fall after the leaves drop and late spring after the seeds fall.
- Trim overhanging branches. Less debris, and fewer branches for squirrels and raccoons to reach the roof from.
What about gutter guards?
Gutter guards (screens, mesh, or solid covers that let water curl in) are an option some homeowners consider under heavy tree cover. They can reduce how often troughs need cleaning, but none eliminate maintenance entirely, and some styles can let snow and ice build up on top in winter or struggle with fine debris like maple seeds and pine needles.
If you’re thinking about guards, raise it during your estimate. We can talk through whether your trough size, roof pitch and tree cover make them worth looking into, and plan the trough so a guard could be added later if you choose.
Repair or replace? 8 signs that point one way or the other
Repair makes sense when the trough itself is sound and the problem is local: one leaky corner, one loose hanger, one blocked downspout. Replace when problems are spread across the system, the trough is sectional and leaking at many joints, or the fascia behind it needs work anyway.
- One corner drips. Usually repairable: clean, reseal and rivet the mitre.
- Several joints along a sectional run leak. Lean toward replacement with seamless.
- A short section sags. Repair by adding hangers, as long as the fascia is solid.
- Sags all along the run, screws spin. The fascia is failing; fix boards and rehang or replace.
- Water pools in the middle after rain. Repair by re-pitching, if the trough isn’t bent.
- Visible splits, holes or rust (on steel). Replace the affected run.
- Overflow every storm despite cleaning. Often a sizing problem; add a downspout or upsize.
- Old spikes-and-ferrules hanging throughout. Replacement with hidden hangers usually costs less over time than repeated re-spiking.
| Question | Points to repair | Points to replace |
|---|---|---|
| How many problem spots? | One or two | Many, or spread around the house |
| Trough type | Seamless in good shape | Sectional with failing joints |
| Fascia condition | Solid | Soft or rotten; trough must come off anyway |
| Capacity | Handles normal storms | Overflows regularly; undersized |
| Age and finish | Colour still acceptable | Faded, dented, mismatched patches |
| Other exterior work planned | None soon | Siding or soffit/fascia being replaced |
If you’re planning new aluminum siding or work on the fascia, doing the eavestrough at the same time avoids taking it down and putting it back twice.
What does eavestrough installation cost in the GTA?
Typical GTA ballpark ranges (2026) — your written quote after an on-site measure is what counts: seamless aluminum eavestrough runs $8–$14 per linear ft for 5″, $10–$17 per linear ft for 6″, and downspouts $10–$18 per linear ft.
| Item | Ballpark range (2026) | Main price drivers |
|---|---|---|
| 5″ seamless aluminum eavestrough | $8–$14 per linear ft | Storey height, corners, access, removal of old trough |
| 6″ seamless aluminum eavestrough | $10–$17 per linear ft | Same, plus fascia suitability for larger trough |
| Downspouts | $10–$18 per linear ft | Size (2″x3″ vs 3″x4″), number of elbows, height |
| Aluminum fascia (if needed) | $7–$13 per linear ft | Board width, custom bends, rot found |
| Rotten fascia board replacement | Quoted once extent is known | Length of damage, rafter condition |
Worked planning example from the ranges
Take a two-storey house with 150 linear ft of eave and 4 downspouts averaging 20 ft each (80 linear ft). In 5″, the trough would fall around $1,200–$2,100 and the downspouts around $800–$1,440, for a combined ballpark of roughly $2,000–$3,540. In 6″, the trough would be around $1,500–$2,550, making the total roughly $2,300–$3,990. Treat these as planning numbers only.
Factors that move your price: height and number of storeys, access around the house, tear-off and disposal of the old system, rotten fascia found, colour choice, the number of corners and custom bends, and season.
How a seamless eavestrough is installed
The job is planned on paper first: outlet positions, slope direction and trough size for each run. Then the old system comes down, the fascia is checked, and the new trough is formed and hung.
- Measure and plan the layout. Each run is measured, roof planes are assessed, and outlet and downspout positions are agreed with you, including where water will discharge.
- Remove the old eavestrough and downspouts. Old troughs, spikes and brackets come off and are hauled away.
- Inspect the fascia. Every board is checked for softness. Rotten sections are replaced before anything else goes up.
- Wrap fascia if part of the job. Custom-bent aluminum fascia goes on first so the trough mounts over a finished surface.
- Snap the slope line. A chalk line marks the pitch from high point to each outlet.
- Form the trough on site. Coil aluminum is run through the seamless machine and cut to length for each run.
- Fit end caps, cut outlets and mitre corners. These are sealed and riveted on the ground where the work is easier to do well.
- Hang the trough. Hidden hangers are spaced along the run and screwed into the fascia, following the slope line.
- Install downspouts. Elbows and downspouts are fastened to the wall with straps, routed to the planned discharge point with an extension or splash pad.
- Water-test. Water is run through each section to confirm it drains to the outlets without pooling or leaks.
- Clean up. Old material and offcuts are removed and the site is cleaned before the final walk-around with you.
Example project scenario: a two-storey under mature maples
Example project scenario (illustrative)
This is an illustrative scenario based on typical GTA jobs, not a specific customer or address.
The house: a 1980s two-storey with a large back roof plane, a front porch roof, and two big maples in the rear yard. The original sectional aluminum troughs were hung with spikes, and both rear downspouts had been connected to the sewer standpipe until the owner disconnected them.
The problems: the back trough overflowed every heavy rain despite cleaning; ice built up at the rear corner each winter and had bent two hangers; and the disconnected downspouts now dumped water onto a patio that sloped toward the house.
What the inspection found: the back fascia was soft for about 12 feet near the corner where ice formed; the rear trough had a dip mid-run; and the 2″ x 3″ downspouts were regularly plugged with maple seeds.
The approach: replace the soft fascia section and wrap the rear fascia in aluminum; install 6″ seamless trough on the back with two 3″ x 4″ downspouts, re-pitched so water ran to each end; relocate one outlet so its extension discharged onto the lawn instead of the patio; and keep 5″ seamless at the front and porch to match the existing look. The owner was pointed to an insulation contractor about the recurring ice, and gutter guards were discussed as an option to revisit after a season with the larger trough.
Ballpark for planning: priced from the 5″ and 6″ per-linear-ft ranges plus downspouts and fascia, with the board replacement itemized separately.
Call and describe what you see. We will tell you honestly whether it is a repair, a replacement or nothing yet.
Template: a seasonal eavestrough care calendar
A simple routine catches small problems before they turn into rotten fascia, wet basements or ice damage. Adjust the timing to the trees around your house.
Template: GTA eavestrough maintenance calendar
- Early spring (after the last hard freeze): look for hangers bent by ice, split corners and crushed downspout elbows. Clear winter debris.
- Late spring: after maple seeds and blossoms fall, clean troughs and flush downspouts. Check extensions and splash pads are in place.
- Summer: during a heavy storm, look (from inside or the ground) for overflow points and note them.
- Late fall: once leaves are down, do the main clean. Remove rain barrels and fit extensions for winter if you use them.
- Winter: watch for icicles in one spot, ice forming along the eaves and water sheeting over the trough during thaws. Don’t chip ice off troughs.
- Any time: note new stains on the fascia or brick below the trough; they often mark a leak.
Questions to ask any eavestrough contractor
- Is the trough seamless, formed on site, and what gauge of aluminum?
- What size trough and downspouts are you proposing, and why for each side?
- What hangers are used, and how far apart?
- How will you check the fascia, and how is rotten wood priced?
- Where will each downspout discharge, and does that meet local rules?
- Is old material removed and disposed of?
- Are you insured for liability and WSIB?
- Is there a written contract and workmanship warranty?
Quick facts behind the advice
These are checkable figures and rules from public sources, listed at the end of this page.
- Mandatory in Toronto: the City says it is mandatory for all Toronto property owners to have their downspouts disconnected from the sewer system.
- Financial assistance: up to $500 toward labour and materials for eligible low-income seniors and persons with disabilities, household income $50,000 or less.
- Cleaning frequency: the City recommends cleaning eavestroughs at least twice a year.
- Snowfall: Environment Canada’s 1981–2010 climate normals for downtown Toronto, as compiled by Current Results, show about 122 cm of snow a year on average, and about 100 cm a year at Pearson Airport over 2010–2019.
- Tree canopy: CanopyTO 2018 estimated Toronto’s canopy at 28.4% to 31%, with Norway maple the most common street tree.
- Ice dams: NRCan identifies heat loss from the attic as the cause and air sealing plus insulation as the preferred prevention.
Eavestrough service across Toronto and the GTA
Our crews travel to homes throughout the region; we don’t operate local branch offices. Conditions vary: older streets in North York and Etobicoke often combine big trees with original fascia, while Toronto homeowners also have the disconnection bylaw to plan around. In Mississauga and other surrounding cities, check local drainage rules before moving downspouts. See every area on our service areas page.
Eavestrough work often goes hand in hand with aluminum trim capping at the roofline. To book a free estimate, call (647) 699-3330 or use our online estimate form.
Every job comes with a written contract and our 5-year workmanship warranty.
Frequently asked questions
Is seamless eavestrough really better than sectional?
For most houses, yes. Sectional troughs have a joint every length, and each joint relies on sealant that eventually fails after years of freeze-thaw. Seamless troughs are formed to the full length of each wall on site, so the only seams are at corners and end caps. Fewer joints means fewer leaks and a cleaner look.
Do I need 6-inch eavestroughs?
Not always. A 5″ trough suits most average roof planes. A 6″ trough is worth it for large or steep roof areas, long runs, upper roofs that drain onto lower ones, or heavy tree cover. Many homes use 6″ only on the problem side. Ballpark pricing is $8–$14 per linear ft for 5″ and $10–$17 for 6″.
How much slope should an eavestrough have?
A common guideline is about 1/4″ to 1/2″ of drop per 10 feet, toward each downspout. That’s enough for water to keep moving without the trough looking crooked. On long runs, pitching from the middle toward downspouts at both ends keeps the drop small. Pooling water after rain is a sign the slope needs correcting.
Does Toronto require downspouts to be disconnected?
Yes. The City of Toronto says it is mandatory for all property owners to have downspouts disconnected from the sewer system, following the Property Standards Bylaw. Water should flow away from the foundation and not onto neighbours’ property, driveways or sidewalks. Exemptions may be possible where disconnection is hazardous or not feasible. Check the City’s website for current details.
I live in Mississauga or Vaughan. Do the same downspout rules apply?
Not necessarily. Toronto’s disconnection program is a City of Toronto requirement. Mississauga, Brampton, Vaughan, Markham, Richmond Hill, Oakville, Pickering and other municipalities set their own drainage and downspout rules. Before changing where your downspouts discharge, check your municipality’s website or call its building or by-law department.
Can new eavestroughs stop ice dams?
No. Ice dams are caused by heat escaping into the attic, melting snow that refreezes at the eaves. Good eavestrough work limits damage with closer hangers, solid fascia and correct slope, but preventing ice dams means air sealing, insulation and ventilation. If thick ice forms every winter, have an insulation or roofing professional assess the attic.
Can you install eavestroughs if my fascia is rotten?
Not until the rotten wood is replaced. Hangers need solid wood to grip, and a trough hung on soft fascia will sag or pull off under ice. We replace damaged boards first, then usually wrap the fascia in aluminum before hanging the new trough. Board replacement is itemized in the written quote.
Do you install gutter guards?
Gutter guards are something to discuss during your estimate rather than a standard part of our eavestrough service. They can cut down on cleaning under heavy trees but don’t remove maintenance entirely, and some styles have winter drawbacks. We can talk through whether they suit your trough size, roof and trees, and plan the system so a guard could be added later.
What warranty comes with eavestrough work?
Every job includes a written contract and a 5-year workmanship warranty. Our crews are licensed and fully insured, carrying liability insurance and WSIB coverage. Aluminum material warranties come from the manufacturer and vary by product, so ask about them when choosing colour and trough size.
Sources
- City of Toronto — Mandatory Downspout Disconnection
- City of Toronto — Mandatory Downspout Disconnection Financial Assistance Program
- Natural Resources Canada — Keeping The Heat In, Section 5: Roofs and attics
- City of Toronto — CanopyTO: 2018 Tree Canopy Study
- Current Results — Toronto snowfall totals and averages (from Environment Canada Canadian Climate Normals 1981–2010)