Aluminum Siding Installation & Replacement in Toronto & the GTA

Replace tired vinyl, old aluminum, wood shingle or composite siding with new aluminum built for GTA freeze–thaw, wind and sun. Costs, comparisons and how we install it.

Updated Written by the Pro Aluminum Siding installation team
On this page
  1. When does it make sense to replace your siding with aluminum?
  2. 9 signs your current siding is ready to come off
  3. Aluminum vs vinyl vs fibre cement vs wood: which siding suits a GTA home?
  4. How the GTA climate is hard on siding
  5. Repair, repaint or replace: how to decide
  6. Tear-off or overlay: should new siding go over the old?
  7. Insulation board and house wrap: what goes behind the siding?
  8. What does aluminum siding cost in the GTA?
  9. How to choose colour and profile for aluminum siding
  10. How we install aluminum siding, step by step
  11. Dents in aluminum siding: why they happen and how to avoid them
  12. How long does aluminum siding last, and what maintenance does it need?
  13. Toronto and GTA homes: what we commonly see
  14. Do you need a permit for new siding?
  15. Example project scenario: replacing tired vinyl on a two-storey semi
  16. Checklist: before your siding estimate
  17. Template: compare siding quotes side by side
  18. Finishing the job: trim, soffit and eavestrough that match
  19. Frequently asked questions
  20. Sources

Quick answer: New aluminum siding is a good fit for GTA homes when the existing vinyl, old aluminum, wood shingle or composite cladding is cracked, faded, dented or letting water in. Expect a typical ballpark of $9–$16 per square foot supplied and installed, with tear-off and insulation board extra. Done properly over sound sheathing and a house wrap, it handles our freeze–thaw winters and summer sun with very little upkeep.

  • Replaces tired vinyl, older aluminum, wood shingle and composite siding
  • Typical GTA ballpark: $9–$16 per sq ft, supply and install (2026)
  • Tear-off, disposal and insulation board are priced as extras
  • Aluminum does not burn, crack in the cold or rot
  • 5-year workmanship warranty, written contract on every job
  • Free estimates by phone or online form

When does it make sense to replace your siding with aluminum?

Replace your siding when the problems are spread across the walls rather than limited to one or two panels. A handful of dents or a single cracked vinyl piece can usually be repaired. Widespread fading, brittleness, loose panels, soft sheathing behind the cladding or water stains inside the house point toward a full replacement.

Aluminum is a sensible choice when you want a rigid, non-combustible cladding with a baked-on finish that does not need painting for many years. It also pairs naturally with aluminum soffit, fascia and trim capping, so the whole exterior can be wrapped in one family of materials and colours.

A lot of the homes we see across Toronto and the surrounding cities are older. According to the City of Toronto’s 2021 Census housing backgrounder, about 29% of households in Toronto live in dwellings built in 1960 or before, and another 29% in dwellings built between 1961 and 1980. Many of those houses have had at least one round of re-siding already, often in an early aluminum or vinyl product that is now at the end of its useful life.

9 signs your current siding is ready to come off

These are the warning signs we look for first during an on-site estimate. One sign on its own may just mean a repair. Three or more, especially on several elevations, usually means replacement will be cheaper over the next ten years than patching.

1. Chalky, faded or blotchy colour

Run your hand over the south and west walls. If a white or coloured powder comes off, the finish is breaking down. Old aluminum chalks; vinyl fades and can turn uneven where one wall gets more sun than another.

2. Cracked, brittle or broken vinyl panels

Vinyl gets stiff in deep cold. Panels that crack from a hockey puck, a snow shovel or a ladder are common after a few decades. Matching an older vinyl profile and colour is often impossible, so repairs stand out.

3. Buckled or wavy walls

Waves in vinyl usually mean it was nailed too tight to allow for expansion. On sunny walls it can bulge each summer. That movement opens joints and lets wind-driven rain behind the panels.

4. Dents and hail marks on old aluminum

Older, thinner aluminum dents easily. A few dents are cosmetic; a wall full of them, plus chalking, is a sign the siding has done its job and is ready to retire.

5. Soft, split or cupped wood shingles

Cedar shingles can be beautiful, but once they split, cup or grow moss, they hold water against the wall. If you are repainting or re-staining every few years and the shingles are still failing, a switch to aluminum ends that cycle.

6. Swollen or delaminating composite siding

Some composite and hardboard sidings swell at the bottom edges and around nail heads when they get wet. Once the edges mushroom or the face flakes, the panel has lost its protection.

7. Water stains, peeling paint or mould inside

Stains on interior walls near windows or under the roofline can mean water is getting behind the cladding. Siding alone is not always the culprit, but it is worth investigating before the damage reaches framing.

8. Loose panels that rattle in the wind

If you hear siding clatter on windy nights, fasteners have pulled or locks have disengaged. Loose panels can blow off in a strong storm and expose the wall.

9. Gaps around windows, doors and corners

Shrunken J-channel, open corner posts and missing caulking all give water a path in. These details are where most wall leaks begin, and they are much easier to rebuild properly during a full re-side.

Aluminum vs vinyl vs fibre cement vs wood: which siding suits a GTA home?

Each material works, but they behave differently in cold, heat and impact. Aluminum wins on fire resistance, cold-weather toughness and low maintenance; vinyl wins on upfront price; fibre cement wins on dent resistance and a heavier, more solid look; wood wins on character but needs the most care.

FactorAluminumVinylFibre cementWood (shingle or clapboard)
Cold weatherStays flexible; does not crack in deep coldBecomes brittle; can crack on impactStable, but needs edges sealed against moistureCan split and check through freeze–thaw
Summer sun and heatBaked finish resists fading well; expands a littleCan fade and warp, especially in dark coloursPainted finish needs periodic repaintingFinish breaks down; needs regular re-coating
FireNon-combustibleCombustible; melts near heat sources like barbecuesNon-combustibleCombustible
Impact and dentsCan dent; thicker gauges resist betterCracks rather than dents in coldVery dent-resistant; can chipDents and gouges, but repairable
Moisture and rotDoes not rot or absorb waterDoes not rotCan absorb water at unsealed cutsRots if water is trapped
MaintenanceWash occasionally; repaint possible late in lifeWash occasionallyRepaint every so oftenStain or paint regularly
Typical GTA ballpark (2026)$9–$16 per sq ft$6–$12 per sq ftAsk for a written quoteAsk for a written quote

Prices above are ballpark estimates only. Your written quote after an on-site measure is what counts.

How the GTA climate is hard on siding

Siding in Toronto and the surrounding region has to cope with freeze–thaw cycles, wind-driven rain and snow, and an increasing number of hot summer days. Choosing the right material and installing it with room to move matter more here than in milder climates.

Freeze–thaw

Water that gets behind siding or into wood trim freezes, expands and pries joints open, then thaws and soaks in deeper. Repeat that through a winter and small gaps become rot. Aluminum itself does not absorb water, but the details around it, such as flashing, J-channel and caulking, have to keep water from getting behind.

Wind and wind-driven rain

Homes near Lake Ontario, on open lots in newer subdivisions, or on hilltops take more wind than homes on sheltered, tree-lined streets. Wind pushes rain sideways into laps and corners and pulls at loose panels. Correct nailing, proper lock engagement and a continuous house wrap are your best defence.

Sun, heat and UV

The City of Toronto’s climate report notes that the downtown station averaged 14 very hot days (above 30°C) a year in 1991–2020, up from about 10 a year in 1961–1990. Sun-facing walls take the brunt of UV, which is why vinyl fades there first. A quality baked aluminum finish holds colour well, but darker colours still absorb more heat and expand more, so installation spacing matters.

Precipitation

The same report puts Toronto’s annual total precipitation at around 819 mm for 1961–1990, with a small increase in 1991–2020. That water, as rain or snow, is what your siding, eavestrough and flashing have to shed every year.

Get a written estimate

We measure on site, explain what we found and put the price in writing. Free, with no pressure.

Repair, repaint or replace: how to decide

Repair when damage is local, repaint when the siding is sound but the colour has failed, and replace when the cladding or the wall behind it has broken down. The table below is the framework we use during an estimate.

SituationRepairRepaintReplace
A few dented or cracked panels on one wallUsually yesNoOnly if a match can’t be found
Old aluminum that is sound but chalkyNoPossible, with proper cleaning and primerBetter value if you also want new colour, trim and insulation
Faded, brittle vinyl across the houseNoNot recommended for most vinylYes
Split or rotting wood shinglesShort-term patching onlyDelays the problemYes
Soft sheathing or water stains indoorsNoNoYes, with sheathing repair first
Planning to add exterior insulationNoNoYes, best done during re-siding

A repaint can refresh sound aluminum, but it will not fix dents, open corners or a missing weather barrier. Replacing does, which tends to tip the decision for long-term owners.

Tear-off or overlay: should new siding go over the old?

A full tear-off is the better choice for most homes because it lets you see and fix the wall underneath. An overlay, where new siding goes over the existing layer, can work in limited cases, but it hides problems and can create a lumpy finish.

When tear-off is the right call

  • There is any sign of water damage, soft sheathing or rot
  • The existing siding is wavy, loose or already layered
  • You want to add insulation board and a new house wrap
  • Window and door trim will need rebuilding to suit a new wall thickness

When an overlay may be considered

  • The existing cladding is flat, firmly attached and dry behind
  • There is no history of leaks
  • Budget does not allow for tear-off and disposal right now

Insulation board and house wrap: what goes behind the siding?

Behind good siding you want a continuous weather-resistive barrier, usually a house wrap, and optionally a layer of rigid insulation board. The wrap stops liquid water and drafts while letting the wall dry; insulation board adds some thermal resistance and gives the siding a flatter base.

House wrap

House wrap should be lapped shingle-style so upper sheets overlap lower ones, taped at seams, and integrated with window and door flashing so water drains outward. Many older homes we open up have torn building paper or none at all, which is one more reason tear-off is worthwhile.

Insulation board

Foam insulation board or fanfold underlayment comes in different thicknesses. Thicker board improves comfort but adds depth that window and door trim must accommodate. Insulation board is priced as an extra because thickness, type and the amount of trim adjustment vary.

What does aluminum siding cost in the GTA?

Typical GTA ballpark ranges (2026) — your written quote after an on-site measure is what counts. Aluminum siding usually runs $9–$16 per square foot supplied and installed, with tear-off, disposal and insulation board extra. The table below lays out how a quote is normally built so you can compare contractors line by line.

Line itemTypical GTA ballpark (2026)What moves it
Aluminum siding, supply and install$9–$16 per sq ftProfile, gauge, colour, storeys, access, wall complexity
Vinyl siding (for comparison)$6–$12 per sq ftGrade, profile, colour
Tear-off and disposalExtra, quoted per jobNumber of layers, material type, bin access
Insulation boardExtra, quoted per jobType and thickness, trim adjustments
Aluminum soffit$8–$14 per linear ftVented vs solid, overhang depth, height
Aluminum fascia$7–$13 per linear ftBoard condition, custom bends
Window capping$175–$450 per windowWindow size, sill and brickmould complexity
Wood rot repair before capping$150–$900 per openingExtent of rot found once trim is opened

A worked example of how the ranges combine

To show how the per-square-foot figure scales, consider a wall area of 1,500 square feet. At the ranges above, supply and install alone would land somewhere between $13,500 and $24,000 before extras. That spread is why an on-site measure matters: a simple, accessible bungalow sits near the lower end, while a tall house with many corners, bay windows and difficult access sits higher. This is arithmetic on the ranges, not a quote.

Factors that push the price up or down

  • Height and storeys. Second and third storeys need more staging and time.
  • Access. Narrow side yards, fences, decks and landscaping slow the work.
  • Tear-off. Removing one or more layers and hauling them away adds labour and disposal.
  • Rot found. Damaged sheathing or trim has to be repaired before cladding goes on.
  • Colour and gauge. Heavier aluminum and some colours cost more.
  • Custom bends. Unusual trim profiles take more shop and site time.
  • Season. Scheduling in busy months can affect timing and sometimes price.

How to choose colour and profile for aluminum siding

Pick a profile that suits the age and style of the house, then choose a colour family that works with the roof, brick and windows you are keeping. The finish is the part of the job you will look at every day, so it is worth bringing samples outside and seeing them in daylight.

Common profiles

  • Horizontal lap (clapboard style). The classic look for postwar bungalows and two-storey houses.
  • Dutch lap. Adds a shadow line that gives a more traditional, hand-crafted feel.
  • Vertical or board-and-batten style. Popular on gables, dormers and modern accents.
  • Wide versus narrow exposure. Narrower reveals suit smaller, older homes; wider reveals read as more contemporary.

Common Canadian siding and trim brands such as Kaycan and Gentek offer a range of aluminum profiles and colours in the market; we can talk through what is available when we visit.

Colour tips that work in the GTA

  1. Start with what you are not changing: roof shingles, brick, stone and window frames.
  2. Look at samples on the sunny side and the shady side of the house.
  3. Remember that darker colours absorb more heat on south and west walls.
  4. Decide early whether soffit, fascia, eavestrough and capping will match or contrast.
Not sure what your home needs?

Call and describe what you see. We will tell you honestly whether it is a repair, a replacement or nothing yet.

How we install aluminum siding, step by step

A durable siding job is mostly about what happens before the first panel goes up. Here is the sequence our crews follow on a typical full replacement.

  1. On-site measure and inspection. We measure each elevation, note windows, doors and penetrations, check access and probe suspect areas for soft wood. You get a written quote that separates siding, tear-off, insulation board and any trim work.
  2. Protect the property. Before tear-off we protect plants, windows, walkways and air-conditioning units, and plan where debris and materials will go.
  3. Remove old siding. Existing cladding is stripped down to the sheathing so we can see the condition of the wall.
  4. Repair the wall. Soft or damaged sheathing is replaced and any rotten trim around openings is dealt with. If repairs go beyond what the quote anticipated, we show you and agree on the change before continuing.
  5. Install insulation board and house wrap. Board goes on if you’ve chosen it, then the house wrap is lapped and taped, and integrated with window and door flashing.
  6. Set starter strip, corners and channels. The starter strip is set level, then outside and inside corners, J-channel around openings and any other trim components go up.
  7. Hang the siding. Panels are locked in course by course and fastened so they can move with temperature changes. Joints are staggered so the wall reads cleanly.
  8. Cap and finish trim. Window and door trim, and any exposed wood, are capped in custom-bent aluminum to match. Penetrations such as vents and hose bibs get proper mounting blocks.
  9. Clean up and walk-through. Debris is removed, the yard is swept for nails, and we walk the house with you to review the work before final payment.

Dents in aluminum siding: why they happen and how to avoid them

Aluminum can dent, and that is the trade-off for its other advantages. Most dents come from predictable sources, and a few smart choices reduce them a great deal.

7 common causes of dents

  1. Balls, hockey pucks and bikes near driveways and side yards
  2. Ladders leaned directly against the siding
  3. Hail on exposed elevations
  4. Lawn mowers and trimmers throwing stones at low courses
  5. Snow shovels and snow blowers hitting the bottom rows
  6. Garbage and recycling bins stored against the wall
  7. Branches rubbing or falling in storms

How to reduce dents

  • Ask about heavier gauge aluminum for high-traffic walls such as the driveway side
  • Use insulation board, which gives panels firmer backing
  • Keep a clear strip at grade and consider a gravel or stone border
  • Use ladder standoffs so ladders rest on the eavestrough or wall framing, not the panel face
  • Store bins and bikes a short distance from the wall

Larger dents usually mean swapping the individual panel, so keep a few spare panels after your job.

How long does aluminum siding last, and what maintenance does it need?

A well-installed aluminum siding job can last for decades, and the metal itself does not rot or crack. What ages is the finish, and the details around openings. Simple maintenance keeps both in good shape. Lifespan depends on exposure, finish quality and care, so treat the matrix below as a maintenance framework rather than a guarantee.

ComponentWhat ages itWhat to doHow often
Siding finishUV, dirt, airborne pollutantsGentle wash with mild soap and a soft brush; avoid high-pressure blasting into lapsOnce a year or as needed
Caulked joints at windows and doorsSun, movement, coldInspect and re-seal where cracked or pulled awayEvery spring
Bottom coursesSplash-back, snow, impactKeep soil, mulch and snow piles awayEach season
Fasteners and locksWind loadsLook for loose or rattling panels after stormsAfter major wind events
Eavestrough aboveLeaves, iceClean so water doesn’t overflow down the wallSpring and fall

Late in its life, sound aluminum siding can be repainted if you want a colour change without a full re-side. That option does not exist for most vinyl.

Toronto and GTA homes: what we commonly see

The GTA has a wide mix of housing, and the right siding approach often depends on the era and style of the home. In the City of Toronto, the 2021 Census shows single-detached houses make up about 23.3% of occupied dwellings, semi-detached about 6.2% and row houses about 5.4%. Those ground-oriented homes are where most siding work happens.

  • Postwar bungalows. Common in areas like Scarborough and Etobicoke, often with brick on the front and older aluminum or vinyl on gables and side walls.
  • 1960s to 1980s split-levels and two-storeys. Common across Mississauga and older parts of the suburbs, often on their second or third round of cladding.
  • Newer subdivision homes. Found throughout Markham and other growing areas, with siding on upper storeys, bays and gables over brick or stone lower walls.

Do you need a permit for new siding?

Usually not for a house, but confirm with your municipality. The City of Toronto’s building permit page lists re-cladding a house or small building of three storeys or less with non-combustible material among the items that do not need a permit (brick and stone veneer are excluded from that exemption). Aluminum is non-combustible.

Rules differ between municipalities and can change, and things like heritage designations or structural repairs found behind the siding can bring different requirements. Always check with your local building department before work begins. Other GTA municipalities each have their own building department and rules.

Example project scenario: replacing tired vinyl on a two-storey semi

Example project scenario (illustrative)

Illustrative only, based on typical GTA jobs, not a specific customer.

The house: A two-storey semi-detached home from the 1970s with brick on the ground floor and original-era vinyl on the upper storey and gable. The vinyl on the south side is faded and cracked; the north wall has a few loose panels that rattle in winter wind.

What the inspection found: Soft sheathing under the window on the south side and no house wrap behind the vinyl. The window trim is painted wood with peeling paint and some rot at the sill corners.

The plan: Full tear-off of the upper-storey vinyl, sheathing repair at the window, new house wrap integrated with window flashing, thin insulation board, and new horizontal aluminum siding in a colour chosen to suit the brick. Wood window trim is repaired and wrapped in matching aluminum capping, and the old soffit and fascia are replaced at the same time so the roofline matches.

Why this approach: Repairing the cracked vinyl would not have addressed the missing weather barrier or the rot. Doing siding, capping, soffit and fascia together means one set of staging and one colour palette across the whole upper storey.

Checklist: before your siding estimate

A little preparation makes the estimate faster and the quote more accurate.

  • Note where you’ve seen leaks, stains or drafts inside the house
  • Photograph any damaged areas you want looked at closely
  • Decide whether you want soffit, fascia, eavestrough or capping priced at the same time
  • Think about colour direction and bring photos of homes you like
  • Check for heritage, condominium or neighbourhood design rules
  • Clear access to side yards and move items stored against the walls
  • List any planned work like new windows that should happen before siding
  • Ask how tear-off, disposal and insulation board are priced

Template: compare siding quotes side by side

Quotes for siding can look very different even when they describe similar work. Use this worksheet to line them up fairly.

Template: siding quote comparison worksheet

  • Contractor name and date of quote: ______
  • Total wall area measured (sq ft): ______
  • Siding material, profile, gauge and colour: ______
  • Price per sq ft for supply and install: ______
  • Tear-off and disposal included? Cost: ______
  • House wrap included? Type and taping: ______
  • Insulation board? Type and thickness, cost: ______
  • How sheathing and rot repairs are priced: ______
  • Window and door trim: capped, rebuilt or left as is: ______
  • Soffit, fascia and eavestrough: included or separate: ______
  • Workmanship warranty length and what it covers: ______
  • Proof of liability insurance and WSIB coverage: ______
  • Written contract provided? Payment schedule: ______
  • Estimated start date and duration: ______

Finishing the job: trim, soffit and eavestrough that match

New siding looks its best when the roofline and openings are finished in the same family of materials. Many homeowners combine siding with aluminum soffit and fascia replacement, new seamless eavestrough and downspouts, and custom-bent aluminum capping on wood trim. If your windows have worn wood brickmould, window capping replacement during the siding job saves a second set-up. Homes with a porch or dormer can have those areas clad at the same time through our porch and dormer cladding service.

Pro Aluminum Siding has more than 10 years of experience on exteriors in Toronto and the GTA. We are licensed and fully insured, with liability insurance and WSIB coverage, every job comes with a written contract, and our workmanship is covered by a 5-year warranty. To book a free estimate, call (647) 699-3330 or use our online estimate request form.

Book a free on-site measure

Every job comes with a written contract and our 5-year workmanship warranty.

Frequently asked questions

Is aluminum siding better than vinyl in Toronto winters?

Aluminum handles cold better than vinyl. Vinyl gets brittle in deep cold and can crack when hit, while aluminum stays flexible and does not crack. Aluminum is also non-combustible. Vinyl costs less upfront and does not dent the same way, so the right choice depends on your budget, how exposed the walls are to impact and how long you plan to stay in the home.

How much does aluminum siding cost per square foot in the GTA?

A typical GTA ballpark for 2026 is $9–$16 per square foot supplied and installed. Tear-off, disposal and insulation board are priced as extras. Height, access, rot repairs, colour, gauge and custom bends all move the number. Your written quote after an on-site measure is what counts.

Can you install aluminum siding over my existing siding?

Sometimes, but we rarely recommend it. An overlay only makes sense when the existing cladding is flat, firmly attached and dry behind, with no leak history. A tear-off lets us inspect and repair the sheathing, add house wrap and insulation board, and rebuild window and door details properly, which usually leads to a longer-lasting wall.

Will new aluminum siding dent easily?

Aluminum can dent from impacts such as balls, ladders, hail and snow equipment. Heavier gauges and insulation board backing make panels more resistant. Keeping bins and bikes off the wall, using ladder standoffs and leaving a clear strip at grade also help. Keep a few spare panels after the job so individual pieces can be swapped if needed.

How long does it take to re-side a house?

Timing depends on the size of the house, number of storeys, tear-off, the amount of rot found and the weather. A modest bungalow takes less time than a tall two-storey with many corners and windows. We give you an estimated start date and duration in the written quote and keep you updated if repairs or weather change the schedule.

Do I need a building permit to replace my siding?

Usually not for a house. The City of Toronto, for example, lists re-cladding a house of three storeys or less with non-combustible material among work that does not need a permit. Other GTA municipalities set their own rules, and heritage properties or structural repairs can change things. Always confirm with your local building department before work starts.

Should I add insulation board when replacing siding?

It is worth considering. Insulation board adds some thermal resistance, gives panels a firmer backing that helps against dents and creates a flatter base. It also adds wall depth, so window and door trim may need adjustment. Because type and thickness vary, insulation board is priced as an extra on your quote.

Can old aluminum siding be painted instead of replaced?

Yes, if it is straight, tight and dry behind. The surface must be washed to remove chalk, primed with a product made for metal and finished with a quality exterior coating. Painting does not fix dents, open corners or a missing weather barrier, so it suits homes where the siding is sound and only the colour has failed.

Do you replace wood shingle and composite siding too?

Yes. We replace vinyl, older aluminum, wood shingle and composite siding with new aluminum. Wood shingle and composite removals often reveal moisture damage behind, so we inspect the sheathing once the old cladding is off and agree any repairs with you before the new siding goes on.

What warranty comes with your siding installation?

Our siding installations come with a 5-year workmanship warranty, and every job is covered by a written contract. We are licensed and carry liability insurance and WSIB coverage. Product warranties on materials are separate and depend on the manufacturer and product selected.

Sources

Call Now: (647) 699-3330